Antifriction and Antiwear Properties of an Ionic Liquid with Fluorine-Containing Anion Used as Lubricant Additive
Authors: Blanco, D., González, R., Viesca, J.L., Fernández-González, A., Bartolomé, M. and Hernández Battez, A.
Journal: Tribology Letters
Volume: 65
Issue: 2
eISSN: 1573-2711
ISSN: 1023-8883
DOI: 10.1007/s11249-017-0846-4
Abstract:Tribological behavior of trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl) imide [P66614][NTf2] ionic liquid (IL) used as additive in a diester oil at concentrations of 0.25, 0.5 and 1 wt% was studied in this research. The IL solubility in the base oil was measured using the inductively coupled plasma mass spectrometry (ICP-MS) technique, and corrosion analysis was done at room temperature at relative humidity of 49–77%. Tribological tests were conducted for 30 min at room temperature, 15 Hz frequency, 4 mm of stroke length, a load of 80 N (corresponding to 2 GPa of maximum contact pressure) and relative humidity of 35–53%. Friction coefficient was recorded during tests, and the wear scar was measured by confocal microscopy. Worn surface was also analyzed by SEM, EDS and XPS. Results showed that a saturated solution of [P66614][NTf2] in the base oil contains about 30 wt% of IL and corrosion activity for the highest concentration of IL (1 wt%) was not found after a 20-day test. Although the base oil and the mixtures had similar friction behavior, only the 1 wt% sample exhibited slightly lower wear volume than the base oil. SEM images exhibited similar wear track width (707–796 µm) and wear mechanism (adhesive) for all samples tested. In addition, the EDS spectra only showed the elements present in the steel. Finally, the XPS measurements could not detect differences regarding iron chemical state among the samples, which is consistent with the tribological behavior obtained.
https://eprints.bournemouth.ac.uk/32965/
Source: Scopus
Antifriction and Antiwear Properties of an Ionic Liquid with Fluorine-Containing Anion Used as Lubricant Additive
Authors: Blanco, D., Gonzalez, R., Viesca, J.L., Fernandez-Gonzalez, A., Bartolome, M. and Hernandez Battez, A.
Journal: TRIBOLOGY LETTERS
Volume: 65
Issue: 2
eISSN: 1573-2711
ISSN: 1023-8883
DOI: 10.1007/s11249-017-0846-4
https://eprints.bournemouth.ac.uk/32965/
Source: Web of Science (Lite)
Antifriction and Antiwear Properties of an Ionic Liquid with Fluorine-Containing Anion Used as Lubricant Additive.
Authors: Blanco, D., Gonzalez, R., Viesca Rodriguez, J.L., Fernandez-Gonzalez, A., Bartolomé, M. and Hernández Battez, A.
Journal: Tribology Letters
Volume: 65
Issue: 2
ISSN: 1023-8883
Abstract:Tribological behavior of trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl) imide [P66614][NTf2] ionic liquid (IL) used as additive in a diester oil at concentrations of 0.25, 0.5 and 1 wt% was studied in this research. The IL solubility in the base oil was measured using the inductively coupled plasma mass spectrometry (ICP-MS) technique, and corrosion analysis was done at room temperature at relative humidity of 49–77%. Tribological tests were conducted for 30 min at room temperature, 15 Hz frequency, 4 mm of stroke length, a load of 80 N (corresponding to 2 GPa of maximum contact pressure) and relative humidity of 35–53%. Friction coefficient was recorded during tests, and the wear scar was measured by confocal microscopy. Worn surface was also analyzed by SEM, EDS and XPS. Results showed that a saturated solution of [P66614][NTf2] in the base oil contains about 30 wt% of IL and corrosion activity for the highest concentration of IL (1 wt%) was not found after a 20-day test. Although the base oil and the mixtures had similar friction behavior, only the 1 wt% sample exhibited slightly lower wear volume than the base oil. SEM images exhibited similar wear track width (707–796 µm) and wear mechanism (adhesive) for all samples tested. In addition, the EDS spectra only showed the elements present in the steel. Finally, the XPS measurements could not detect differences regarding iron chemical state among the samples, which is consistent with the tribological behavior obtained.
https://eprints.bournemouth.ac.uk/32965/
Source: BURO EPrints